Hello,
I am a newbie with netX. I downloaded netX90_PNSV5_simpleConfig.zip file from Hilscher's website and after unzip, I imported into netX Studio CDT.
After that, I want to build that project so Build>Build Solution try to build it.
I faced some errors in it. So, can you help to resolve it?
I attached a snapshot of my error.
I am now running bluetooth container on netPI Core V1.2.0.0. I am able to scan some devices as below attached.
how I can access data from "connected" bluetooth device into netPI? Is there any simulation tool/application to run on netPI? I searched in other threads in this forum, where I found BlueZ. Is it the software used ?
Requirement: One of my customer wants to connect Bluetooth Sensor to netPI & want to read sensor data, For that we are preparaing demo on Bluetooth access.
I am investigating how we can use the Hilscher netPI RTE 3 with the standard GSD file in the short term to implement a project with a short time to market. I have a few questions.
The netPI programming example uses a modified version of the V3.5.35 – V3.x file. However there are three later files in SYCON.net:
V3.5.7 – V3.5.17
V4.2.0.0 – V4.3.0.x
V4.4.0.x
Can you confirm which NETX 51 RE/PNS GSD file I should use or can any of the files be used? I assume that the V4.X.X.X files require a netX51 V4 firmware as the major firmware version incompatibility was the initial issue I had when setting up the NHST-T100-EN/PNM. Is this correct? It so is this available for the netPI or do I need to stick to V3.5X.X files?
The GSD file supports the following (lifted from the Hilscher documentation PROFINET IO Device V3.12.0 | Protocol API DOC111110API17EN and SYCON.net tool):
Total cyclic input data: 1440 bytes
Total cyclic output data: 1440 bytes
Maximum number of submodules: 255 submodules per Application Relation at the same time, 1000 submodules can be configured
I am slightly confused by the use of terminology in the documentation and SYCON.net. The documentation refers to submodules yet I only appear to be able to configure modules (each module added appears to result in a non-editable submodule) and the SYCON.net tool appears to be counting the number of slots used in addition to octets (bytes) not submodules. I have attached a screenshot.
Until I get access to the PI GSDML specification I cannot apply meaning to the entire Hilscher GSD file specification. This is on-going (purchase of PI membership has been approved for the project) and hopefully will be resolved shortly.
I have NIOT-E-NPI3-EN hardware, I installed Node red image in a docker container, node red works fine for a few minutes after that getting error "This site can’t be reached" in the browser, in this case, if I do container restart it works for a few minutes, again the same issue comes.
I have already made changes to the "Process data" in/out sizes in GSDML file + App.h file.
Now I want to go a step further and set/get "on demand" fields both in application(App.h) side and GSDML file.
Do you provide a sample how it should be done or direct where can I found information/tools how it could be done ?
few use cases:
1. configure the device to work in specific mode.
2. get async event from device something is out of order ( IRT,<IsochroneMode IsochroneModeRequired/> from GSDML_GettingStarted_en.pdf)
Can you please provide some info regarding this need ?
I have a problem with netPi dashboard in Node-RED after rebuilding the docker. The netPi seems to be built in IIoT Gateway 70077 of company ETS DIDACTIC GMBH. They want me to send in the IIoT gateway to service, but this is not possible due to time constraints.
Maybe you have a suitable solution. Thank you very much.
Failure description:
Product:
NIOT-E-NPI3-51-EN-RE (netPI)is built in IIoT Gateway 70077 of company ETS DIDACTIC GMBH
Problem:
After „Rebuild“ of Docker, the official Node-RED Dashboard has to be installed again.
After a new installation of the dashboard, neither the node-RED nor the dashboard can be accessed.
Complete restarts of the computer, the gateway and the docker do not solve the problem.
Conjecture:
After rebuilding the Docker, only the latest version of the dashboard (2.19.3) is available.
Probably the non-updatable Node-RED version (0.17.3) does not work with the new dashboard version.
For the project i need to connect a monitor to the netPI and get a console screen on the Monitor. Currently as I understand from the entrypoint.sh the Monitor just outputs the output the boot process and hangs. Is there a way to get the console screen in the Monitor connected to netPI via HDMI
our netPi stopped working, the docker.service does not start up anymore. (docker.service: Failed with result 'protocol')
How can we fix this? WebInterface is working. Firmware version V1.2.0.0
Any help would be welcome. What may produce this? Power failure?
syslog of boot process attached.
