• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[SOLVED] Access problems
#1
Hello ,

 I can't seem to access my netPi anymore so I'm trying to reset it to factory setting using several USB sticks but can't seem to get
through. Node red got blocked and i couldn't delete the flows so i tried getting back to factory setting but now i can neither access the
device properly nor reset it.

what can I still do?

 Thanks,

Azzam
  Reply
#2
Well what you can always do is connecting a display to the HDMI connector and watch the boot procedure of the device. There you can see if the USB sticks (with/without) is recognized.
Plese full format the FAT32 file system ... the best is doing that untr Linux (if you have). Quick Format usuall don't work.
Also make sure you named the USB volume correctly to value RECOVERY. Else it will not be recognized at all.

By the way which device exactl are you using. What is the name of your device on th label. Maybe you are using the wrong software for the wrong device. Make sure you exctract the software 1.1.3.0 files provided on the netPI web site before you put them on the USB.

Thx
Armin
You never fail until you stop trying.“, Albert Einstein (1879 - 1955)

  Reply
#3
So this is the error i'm getting any Idea how to fix it?


Attached Files Thumbnail(s)
   
  Reply
#4
Is this all in the screenshot what your netPI is reporting?

How about if you insert the USB stick into one of the slots?

Normally netPI prints out the USB devices found in the log file.
You never fail until you stop trying.“, Albert Einstein (1879 - 1955)

  Reply
#5
yes this is all my netPI is reporting and sure the USB Stick was already inserted.
  Reply
#6
Ok and how is the screen shot in case you do not apply the USB stick. The same?
You never fail until you stop trying.“, Albert Einstein (1879 - 1955)

  Reply
#7
(November-27th-2018, 12:25 PM)Armin@netPI Wrote: Is this all in the screenshot what your netPI is reporting?

How about if you insert the USB stick into one of the slots?

Normally netPI prints out the USB devices found in the log file.

It did print out the log files of the USB stick but then entered another window as shown in the screen shot.
Any suggestion?

Thank you in advance !

 Azzam

(November-27th-2018, 03:10 PM)Armin@netPI Wrote: Ok and how is the screen shot in case you do not apply the USB stick. The same?

If i don't insert a USB Stick it goes directly to this same dialouge

So basicly this is what I'm getting.

 Thanks again


Attached Files Thumbnail(s)
           
  Reply
#8
So your netPI is not dead and basically alive. If I see your first of three screen shots I see a term like "4 USB devices found" right at the beginning. This term should change in case a USB stick is inserted with RECOVERY volume label to a value "5 USB devices found". Is it?

Then the log comes to a point where it says "reading fit image". If a valid image was found on the USB stick it says the same but tell you it is booting from USB instead of mmc0. I can't tell exactly since I am not in the office and cannot reproduce it this week. But does it?
You never fail until you stop trying.“, Albert Einstein (1879 - 1955)

  Reply
#9
Contrary to the assumption you had a netPI device, we have recognized your device as Edge Gateway named "Connect" when you returned it to us.

These type of devices and of course netPI are supporting you on communications at the IT/OT edge. But our Edge Gateways have plenty of software more installed than plain Docker as on netPI. This offers you indeed multiple vectors to get such a device into a non-bootable state which was the root cause of your problem.

We sent you back a replacement device.

Thx
Armin
You never fail until you stop trying.“, Albert Einstein (1879 - 1955)

  Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Wi-fi in Access Point mode Renato75 7 4,648 June-3rd-2022, 12:59 PM
Last Post: Armin@netPI
  NetPI wifi access to WPA2-Enterprise MikeP 4 4,253 September-3rd-2021, 02:56 PM
Last Post: MikeP
  netPI RTE 3: access from several comm. masters tad 3 4,024 June-3rd-2021, 12:03 PM
Last Post: Armin@netPI
  Access to RTC from my own container application tad 1 3,520 March-19th-2021, 02:58 PM
Last Post: Armin@netPI
  Bluetooth Access MGharat 10 8,534 February-25th-2020, 12:58 PM
Last Post: DSongra
Wink How to access Root Directory Rajesh3128 8 5,068 October-16th-2019, 11:19 AM
Last Post: Armin@netPI
  netPI access for remote PLC confign MGharat 3 4,863 October-15th-2019, 09:12 AM
Last Post: Armin@netPI
  [SOLVED] Help with fieldbus node Farani 5 3,873 August-20th-2019, 07:22 AM
Last Post: Armin@netPI
  BLE pairing problems with bluez 5.50 abmn 1 4,242 August-8th-2019, 08:51 AM
Last Post: Armin@netPI
  [SOLVED] How to update firmware philippbruhin.ch 12 9,084 July-16th-2019, 11:20 AM
Last Post: patrick

Forum Jump:


Users browsing this thread: 1 Guest(s)